Skip to content
Home Inspection Software
home inspection software photo editing view nachi home inspector association Home Inspection Software allowing you to create easy to read, customizable reports that can be uploaded online, emailed, or printed out on the job site. Runs on Windows, Mac & Linux!
ASHI home inspection software screenshot.png Create a professional looking home inspection website for $24.99 a month. We give you all the tools you need to create a site and get it to the top of the search engines. No previous skills required!
Home Inspector Pro Forum
May 19, 2013, 04:00:08 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
   Home   Help Search Login Register  
Pages: [1]   Go Down
  Print  
Author Topic: Question on overhead exterior wiring  (Read 1136 times)
Kyu Hwang Chung
Member
*

Karma: 0
Offline Offline

Posts: 35


View Profile
« on: October 16, 2011, 10:57:21 PM »

Hello, everyone,
There is a overhead exterior wiring from electric meter to the garage.
This no Conduit wiring can be Ok? Clearance is prox. 1 ft from garage roof top.  (please see attached)
Please advise..
Thank you !


* 0 038.JPG (41.6 KB, 640x427 - viewed 114 times.)

* 0 037.JPG (55.68 KB, 640x427 - viewed 112 times.)
Logged
Cameron Anderson
Sr. Member
****

Karma: 22
Offline Offline

Peoria, IL
Posts: 430



View Profile WWW
« Reply #1 on: October 18, 2011, 09:43:25 PM »

Kyu,

Yes, there are times where insulated exterior-rated wiring is run overhead for out-buildings. There are some problems though with the installation in your photos.

1. There are no guy-wires supporting the wiring to the garage. This means the wiring is under considerable tension and there is the risk of damage to the wires themselves.
2. The standard for clearance at the garage would most likely be the same as a main service drop which is 18" I believe.

There are several other parts to this installation which should be considered as well. What does the wiring pass over and what are the clearances to objects below? What type of wiring and what size of wire is present, is it properly sized and rated? How are the mastheads secured and how tight is the wiring pulled?

I'm sure some other guys can give you a few more thoughts as well.
Logged

Title: Home Inspection Peoria, IL
URL:  www.aaintegrityhomeinspection.com
Bill Warner
Sr. Member
****

Karma: 11
Offline Offline

Posts: 256


There's a fine line between comedy and humor...


View Profile WWW
« Reply #2 on: October 19, 2011, 01:18:06 AM »

Yes, standard service drop clearances apply.
Additionally to what Cameron posted, the NM sheathing must be rated for UV exposure (the sheathing will be identified by a stamp or marking stating it as such). If it is not rated for UV exposure, it is an incorrect application and should be corrected.

But based on your photos, there are some readily visible issues that pose potential safety concerns such as lack of drip loop, support wires (as Cameron stated,) and potential clearance issues over the roof.  My opinion, the sheathing on those wires does not appear UV rated and I would look closely for deteriorated sheathing/insulation, and exposed conductors
Logged

Bill Warner
Dayton Infrared Thermal Inspection
http://DaytonThermalInspection.com
Infrared Thermal Imaging Inspections Serving Dayton, Cincinnati, and Greenville Ohio
For a Link Exchange please EMAIL ME your info
Kyu Hwang Chung
Member
*

Karma: 0
Offline Offline

Posts: 35


View Profile
« Reply #3 on: October 19, 2011, 04:26:25 AM »

Thanks, bill and Cameron.
Your advise is very helpful for me.
Tank you again !  ^__^
Logged
Pages: [1]   Go Up
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.15 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!